Location: > Product Center > Drying

Drying

Product Center

XF series horizontal boiling dryer

Introduction: product descriptionBoiling drying, also known as fluidized bed, is composed of air filter, heater, fluidized bed host, cyclone separator, bag filter, high-pressure centrifugal fan, and operating table. Due to the different nature of the dried material…

Hotline: 0086-15380092122
Inquiry

product description
  Boiling drying, also known as fluidized bed, is composed of air filter, heater, fluidized bed host, cyclone separator, bag filter, high-pressure centrifugal fan, and operating table. Due to the different nature of the dried materials, when supporting dust removal equipment , Can be considered according to needs, you can choose cyclone separator, bag filter at the same time, you can also choose one of them, generally speaking, if the specific gravity is larger, such as granules and granular materials, you only need to choose the cyclone separator, and the small particles with lighter specific gravity For powdery and powdery materials, a bag filter is required, and a pneumatic feeding device and belt conveyor are available for selection.
  Bulk granular solid materials are fed into the fluidized bed dryer by the feeder, and the filtered clean air is heated and sent to the bottom of the fluidized bed by the blower. The distribution plate contacts the solid materials to form a fluidized heat and mass exchange of gas and solid. After the material is dried, it is discharged from the discharge port, and the waste gas is discharged from the top of the fluidized bed through the cyclone dust collector and the bag dust collector to recover the solid powder and emptied.
  Steam, electric and hot blast stoves can all be equipped (according to user requirements).

working principle
  The clean hot air is distributed into the bed through the valve plate, and the wet material entering from the feeder is boiled by the hot air. Because the hot air is in extensive contact with the material, the heat and mass transfer process is enhanced, so it can be dried in a relatively short time. If the continuous type is used, the material enters from one end of the bed, after tens of seconds to a few minutes, boiling and drying, and automatically flows out from the other end of the bed. This equipment is generally operated under negative pressure.
Adapt to materials
  ◎Drying operations of medicines, chemicals, raw materials, food, grain processing, and feed. Such as: drying and dehumidification of raw materials, tablet granules, Chinese medicine granules, health food, beverage granules, corn germ, feed, plastic resin, citric acid and other powdered materials. The particle size of the applicable materials is generally 0.1-6mm, and the recommended particle size is 0.5-3mm.

Schematic

卧式沸腾干燥机结构示意图

Installation Notes
◎Each equipment should be placed flat and fixed with foot screws, and all parts should be well sealed.
◎The fan can be placed outdoors or in a self-built muffler room. The layout can be adjusted according to the actual situation.

Specification model
Technical Parameters
XF0.25-1
(originalXF10)
XF0.25-2
(originalXF20)
XF0.25-3
(originalXF30)
XF0.25-6 XF0.3-2 XF0.3-4 XF0.3-6 XF0.3-8 XF0.3-10

XF0.4

-4

XF0.4-

6

Bed area(m2) 0.25 0.5 1.0 1.5 0.6 1.2 1.8 2.4 3.0 1.6 2.4
Drying capacity
(kg h2O/h)
10-15 20-25 30-45 52-75 -30 42-60 63-90 84-120 105-150 56-80 84
Fan power(kw) 5.5 7.5 15 22 7.5 18.5 30 37 48 30 37

Inlet air 

temperature()

120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140

Material 

temperature()

40-60 40-60 40-60 40-60 40-60 40-60 40-60 40-60 40-60 40-60 40-60
Host size

Length×width

×height(m)

1×0.6 2×0.6 4×0.6 6×0.6 2×0.70 4×0.7 6×0.7 8×0.7 10×0.7 4×1 6×1
Land area(m2) 18×3.35 25×3.35 35×3.35 40×3.35 25×3.4 38×3.4 45×3.4 56×3.4 70×3.4 18×3.58 56×3.58

 

Specification model
Technical Parameters
XF0.4-8 XF0.4-10 XF0.4-12 XF0.5-4
(原XF50)
XF0.5-6 XF0.5-8 XF0.5-10 XF0.5-12 XF0.5-14 XF0.5-16 XF0.5-18
Bed area(m2) 3.2 4.0 4.8 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0
Drying capacity
(kg h2O/h)
112-160 140-200 168-240 70-100 140-200 140-200 175-250 210-300 245-350 280-400 315-450
Fan power(kw) 44 66 66 30 66 66 90 90 150 150 165
Inlet air temperature() 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140 120-140
Material temperature() 40-60 40-60 40-60 40-60 40-60 40-60 40-60

40-60

40-60 40-60 40-60
Host size
Length×width×height(m)
8×1 10×1 12×1.2 4×1.2 8×1.2 8×1.2 10×1.2 12×1.2 14×1.2 16×1.2 18×1.2
Land area(m2) 74×3.58 82×3.58 96×4.1 50×4.1 70×4.1 82×4.1 100×4.1 140×4.1 180×4.1 225×4.1 268×4.1

Note: 1. Feeding method: 1. Star feeding; 2. Star feeding and pneumatic conveying combined use; 3. Belt conveying; 4. User-defined. 2. Automatic production can be realized. 3. In addition to the above models, special designs can be made for users. 4. According to different materials, the fan power is also different.

Photo Gallery
  • Horizontal boiling dryer
  • Horizontal boiling dryer
Application Customers
Video Collection

    No record yet.
Animations

Related Projects
No record yet.
Relevant Articles
Related Products

Copyright © Jiangsu Guojin Drying Technology Co., Ltd. All rights reserved [Manage]
.Support: Eastnet Network support:China Drying Equipment

Scan QR code