Location: > Product Center > Drying

Drying

Product Center

PLG series disc continuous dryer

Introduction: product descriptionDisc continuous dryer is a highly efficient conductive continuous drying equipment. Its unique structure and working principle determine that it has the characteristics of high thermal efficiency, low energy consumption, small footp…

Hotline: 0086-15380092122
Inquiry

product description
  Disc continuous dryer is a highly efficient conductive continuous drying equipment. Its unique structure and working principle determine that it has the characteristics of high thermal efficiency, low energy consumption, small footprint, simple configuration, convenient operation and control, and good operating environment. It is widely used in chemicals, medicine, pesticides, food, feed, and agriculture. Drying operations in industries such as by-product processing. It is well received in practice in various industries. Now it produces three types of atmospheric pressure, airtight, vacuum, 1200, 1500, 2200, 3000 four types, A (carbon steel), B (stainless steel in contact with materials), C (on the basis of B, add steam pipes) The road, main shaft and bracket are made of stainless steel, and the cylinder and cover are lined with stainless steel). Three kinds of materials, a drying area of 4~180m2, a total of hundreds of models of series products, and can provide a variety of auxiliary equipment to meet the needs of users for drying various materials.
working principle
  The wet material is continuously added to the drying plate on the first layer of the upper part of the dryer from the feeder, and the rake arm with the rake blades makes a rotary motion to make the rake arm rotate to make the rake blades continuously turn over the material. The material flows through the surface of the drying plate along an exponential spiral. The material on the small drying plate is moved to the outer edge, and falls on the outer edge to the outer edge of the large drying plate below. On the large drying plate, the material moves in and falls from the middle. The material opening falls into the following small drying plate. The large and small drying trays are arranged alternately up and down, so that the material can continuously flow through the entire dryer. A heating medium is introduced into the hollow drying plate. The heating medium is in the form of saturated steam, hot water and heat-conducting oil. The heating medium enters from one end of the drying plate and exits from the other end. Dried materials fall from the bottom drying plate to the bottom of the shell, and then are moved to the discharge port by the harrows for discharge. The moisture escapes from the material and is discharged through the moisture discharge port provided on the top cover, and the moisture of the vacuum type disc dryer is discharged from the vacuum pump port provided on the top cover. The dry materials discharged from the bottom layer can be directly packaged. By adding finned heater, solvent recovery condenser, bag filter, dry material backmixing mechanism, induced draft fan and other auxiliary equipment, it can improve its drying production capacity. Dry paste and heat sensitive materials can be easily recovered Solvent, and can perform pyrolysis and reaction operations.
Performance characteristics
(1) Easy regulation and strong applicability
◎By adjusting the thickness of the material layer, the rotation speed of the main shaft, the number of harrow arms, the type and size of the harrow blades, the drying process can be better.
◎Each layer of the drying tray can be heated or cooled by heating or cooling the material through the heating or cooling medium alone, and the material temperature control is accurate and easy.
◎The residence time of materials can be adjusted accurately.
◎Single flow direction of materials, no back-mixing phenomenon, uniform drying, stable quality, no need for re-mixing.
(2) Simple and easy operation
◎The driving and stopping operation of the dryer is very simple.
◎After stopping the feed, the transporting material dirt rake leaves can quickly empty the material in the dryer.
◎Through the special sight glass of the large inspection door, the inside of the equipment can be carefully cleaned and observed.
(3) Low energy consumption
◎The material layer is very thin, the spindle speed is low, the power required by the material conveying system is small, and the power consumption is low.
◎Drying by conduction heat, high thermal efficiency and low energy consumption.
(4) The operating environment is good, the solvent can be recycled, and the dust emission meets the requirements
◎Atmospheric pressure type: Due to the low air velocity in the equipment and the high humidity distribution in the equipment, it is difficult for dust to float to the top of the equipment, so the exhaust from the top moisture exhaust port contains almost no dust.
◎Closed type: equipped with a solvent recovery device, which can easily recover the organic solvent in the wet gas. The solvent recovery device is simple and the recovery rate is high. For flammable, explosive, toxic and easily oxidized materials, nitrogen can be used as a moisture-carrying gas for closed-circuit circulation to make it safe to operate. It is especially suitable for drying flammable, explosive and toxic materials.
◎Vacuum type: A disc dryer operated under vacuum, especially suitable for drying heat-sensitive materials.
(5) Convenient installation and small floor space
◎The dryer leaves the factory as a whole and is transported as a whole. It only needs to be hoisted in place, making the installation and positioning very easy.
◎Due to the layered arrangement and vertical installation of the drying plate, even if the drying area is large, the floor space is small.

盘式连续干燥机
Technical characteristics
(1) Drying plate
◎Design pressure: Generally 0.4MPa, the upper limit can reach 1.6MPa.
◎Working pressure: Generally ≤0.4MPa, the upper limit can reach 1.6MPa.
◎Heating medium: steam, hot water, heat-conducting oil, hot water heating at 100℃, 100℃~150℃ saturated steam or superheated steam ≤0.4MPa, 150℃~320℃ heat-conducting oil For heating, electricity, heat-conducting oil, molten salt, etc. can be used for heating above 320°C.
(2) Material delivery system
◎Spindle speed: 1~10 rpm, electromagnetic or frequency conversion stepless speed regulation.
◎Rake arms: There are 2-8 rake arms fixed on the main shaft on each drying plate.
◎Rake leaves: hinged on the rake arm, can keep contact with the surface of the disk floating up and down, there are many forms.
◎Rolling: For materials that are easy to agglomerate and need to be crushed, adding rollers at appropriate positions can enhance the heat transfer and drying process.
(3) The shell has three types: normal pressure, airtight, and vacuum
◎Atmospheric pressure type: cylinder or octagonal prism type, with integral and split structure. The main pipeline of the heating medium inlet and outlet can be inside the shell or outside the shell.
◎Closed type: cylindrical shell, can withstand 5Kpa internal pressure, heating medium inlet and outlet main pipeline can be inside or outside the shell.
◎Vacuum type: cylindrical shell, the design pressure is 0.1Mpa, the main pipeline of heating medium inlet and outlet is in the shell.
(4) Air heater
Generally used in the case of large evaporation to enhance drying efficiency.
Adapt to materials
Drying Pyrolysis Combustion Cooling Reaction Sublimation
Organic chemical products, inorganic chemical products, medicine, food, feed, fertilizer

specification Outer diameter mm height mm Dry area m2 power Kw
1200/4 Φ1850 2718 3.3 1
1200/6 3138 4.9
1200/8 3558 6.6 1.5
1200/10 3978 8.2
1200/12 4398 9.9 2.2
1500/6 Φ2100 3022 8.0
1500/8 3442 10.7
1500/10 3862 13.4
1500/12 4282 16.1 3.0
1500/14 4702 18.8
1500/16 5122 21.5
2200/6 Φ2900 3319 18.5
2200/8 3739 24.6
2200/10 4159 30.8 4.0
2200/12 4579 36.9
2200/14 4999 43.1 5.5
2200/16 5419 19.3
2200/18 5839 55.4 7.5
2200/20 6259 61.6
2200/22 6679 67.7 11
2200/24 7099 73.9
2200/26 7519 80.0

 

specification Outer diametermm height mm Dry area m2 power Kw
2500/6 Φ3150 3319 26.3 4
2500/8 3739 35
2500/10 4159 43.8 5.5
2500/12 4579 52.5
2500/14 4999 61.3 7.5
2500/16 5419 70
2500/18 5839 78.8 11
2500/20 6259 87.5
2500/22 6679 96.3
2500/24 7099 105 13
2500/26 7519 113.8
3000/8 Φ3800 4050 48 11
3000/10 4650 60
3000/12 5250 72
3000/14 5850 84
3000/16 6450 96
3000/18 7050 108 13
3000/20 7650 120
3000/22 8250 132
3000/24 8850 144
3000/26 9450 156 15
3000/28 10050 168
Photo Gallery
  • Disc continuous dryer
  • Disc continuous dryer
  • Disc continuous dryer
Application Customers
Video Collection

    No record yet.
Animations

Related Projects
No record yet.
Relevant Articles
Related Products

Copyright © Jiangsu Guojin Drying Technology Co., Ltd. All rights reserved [Manage]
.Support: Eastnet Network support:China Drying Equipment

Scan QR code